HDD - 8 bad sectors
Screenshot from "Disks" utility
Screenshot from "Logs" utility
fdisk -l /dev/sdb command gives this: fdisk: cannot open /dev/sdb: Input/output error
smartctl -a /dev/sdb returns this:
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.18.0-13-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: ST2000LM007-1R8174
Serial Number: WDZ447EV
LU WWN Device Id: 5 000c50 0a9631d82
Firmware Version: RDM1
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sun Dec 23 23:25:25 2018 EET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x51) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 328) minutes.
SCT capabilities: (0x303d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 083 064 006 Pre-fail Always - 206647660
3 Spin_Up_Time 0x0023 099 099 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 751
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x002f 077 060 045 Pre-fail Always - 17381474631
9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 3407 (214 118 0)
10 Spin_Retry_Count 0x0033 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 691
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0033 100 100 097 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 070 047 040 Old_age Always - 30 (Min/Max 27/31)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 197
192 Power-Off_Retract_Count 0x0022 100 100 000 Old_age Always - 38
193 Load_Cycle_Count 0x0032 082 082 000 Old_age Always - 36047
194 Temperature_Celsius 0x0022 030 053 000 Old_age Always - 30 (0 14 0 0 0)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 8
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 223 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 223 occurred at disk power-on lifetime: 3356 hours (139 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 01 00 00 00 40 00 01:13:14.487 READ DMA EXT
25 00 01 00 00 00 40 00 01:13:14.471 READ DMA EXT
25 00 01 00 00 00 40 00 01:13:14.333 READ DMA EXT
25 00 01 00 00 00 40 00 01:13:14.256 READ DMA EXT
25 00 01 00 00 00 40 00 01:13:14.172 READ DMA EXT
Error 222 occurred at disk power-on lifetime: 3356 hours (139 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 01 00 00 00 40 00 01:13:14.487 READ DMA EXT
25 00 01 00 00 00 40 00 01:13:14.471 READ DMA EXT
25 00 01 00 00 00 40 00 01:13:14.333 READ DMA EXT
25 00 01 00 00 00 40 00 01:13:14.256 READ DMA EXT
25 00 01 00 00 00 40 00 01:13:14.172 READ DMA EXT
Error 221 occurred at disk power-on lifetime: 3356 hours (139 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 01 00 00 00 40 00 01:13:14.471 READ DMA EXT
25 00 01 00 00 00 40 00 01:13:14.333 READ DMA EXT
25 00 01 00 00 00 40 00 01:13:14.256 READ DMA EXT
25 00 01 00 00 00 40 00 01:13:14.172 READ DMA EXT
25 00 01 00 00 00 40 00 01:13:14.084 READ DMA EXT
Error 220 occurred at disk power-on lifetime: 3356 hours (139 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 01 00 00 00 40 00 01:13:14.333 READ DMA EXT
25 00 01 00 00 00 40 00 01:13:14.256 READ DMA EXT
25 00 01 00 00 00 40 00 01:13:14.172 READ DMA EXT
25 00 01 00 00 00 40 00 01:13:14.084 READ DMA EXT
b0 d0 00 00 4f c2 00 00 01:13:11.036 SMART READ DATA
Error 219 occurred at disk power-on lifetime: 3356 hours (139 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 00 00 00 00 Error: UNC at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 01 00 00 00 40 00 01:13:14.256 READ DMA EXT
25 00 01 00 00 00 40 00 01:13:14.172 READ DMA EXT
25 00 01 00 00 00 40 00 01:13:14.084 READ DMA EXT
b0 d0 00 00 4f c2 00 00 01:13:11.036 SMART READ DATA
b0 d0 00 00 4f c2 00 00 01:13:02.378 SMART READ DATA
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Aborted by host 50% 3367 -
# 2 Extended offline Completed: read failure 90% 3355 450623616
# 3 Extended offline Completed: read failure 90% 3351 450623616
# 4 Short offline Completed without error 00% 3351 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
In Windows nor Device Manager nor Disk Manager show the drive. Only Ubuntu can see the drive. Is there any way to fix it ?
Ben Wick
0 Answers
Nobody has answered this question yet.
User contributions licensed under CC BY-SA 3.0