Raspberrypi4 WiFi is not working using core-image-full-cmdline

As i see in the documentation that wifi is already added by default to core-image-base, i have test it and wifi works well. However when i use core-image-full-cmdline, wifi doesn't work. when i run ifup wlan0

Successfully initialized wpa_supplicant
rfkill: Cannot get wiphy information
Could not read interface wlan0 flags: No such device
WEXT: Could not set interface 'wlan0' UP
wlan0: Failed to initialize driver interface

run ifconfig -a

eth0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        ether dc:a6:32:3c:fd:0e  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 2  bytes 140 (140.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 2  bytes 140 (140.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

so, could i add IMAGE_INSTALL_append = " linux-firmware-bcm43455 but it have been added here here is my bootlog file

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.10.17-v7l (oe-user@oe-host) (arm-poky-linux-gnueabi-gcc (GCC) 10.2.0, GNU ld (GNU Binutils) 2.35.1) #1 SMP Mon Mar 1 09:44:55 UTC 2021
[    0.000000] CPU: ARMv7 Processor [410fd083] revision 3 (ARMv7), cr=30c5383d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt: Machine model: Raspberry Pi 4 Model B Rev 1.1
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] Reserved memory: created CMA memory pool at 0x000000002ac00000, size 64 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000000000-0x000000002fffffff]
[    0.000000]   Normal   empty
[    0.000000]   HighMem  [mem 0x0000000030000000-0x000000007fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000003b3fffff]
[    0.000000]   node   0: [mem 0x0000000040000000-0x000000007fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff]
[    0.000000] On node 0 totalpages: 504832
[    0.000000]   DMA zone: 2304 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 196608 pages, LIFO batch:63
[    0.000000]   HighMem zone: 308224 pages, LIFO batch:63
[    0.000000] percpu: Embedded 20 pages/cpu s51148 r8192 d22580 u81920
[    0.000000] pcpu-alloc: s51148 r8192 d22580 u81920 alloc=20*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 502528
[    0.000000] Kernel command line: coherent_pool=1M 8250.nr_uarts=0 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 bcm2708_fb.fbwidth=1920 bcm2708_fb.fbheight=1080 bcm2708_fb.fbswap=1 smsc95xx.macaddr=DC:A6:32:3C:FD:0E vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000  dwc_otg.lpm_enable=0 root=/dev/mmcblk0p2 rootfstype=ext4 rootwait
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] software IO TLB: mapped [mem 0x0000000025400000-0x0000000029400000] (64MB)
[    0.000000] Memory: 1844076K/2019328K available (10240K kernel code, 1386K rwdata, 3236K rodata, 2048K init, 910K bss, 109716K reserved, 65536K cma-reserved, 1232896K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] ftrace: allocating 33813 entries in 67 pages
[    0.000000] ftrace: allocated 67 pages with 3 groups
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000]  Rude variant of Tasks RCU enabled.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] random: get_random_bytes called from start_kernel+0x3c4/0x5a8 with crng_init=0
[    0.000008] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns
[    0.000036] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns
[    0.000099] bcm2835: system timer (irq = 25)
[    0.000700] arch_timer: cp15 timer(s) running at 54.00MHz (phys).
[    0.000720] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xc743ce346, max_idle_ns: 440795203123 ns
[    0.000742] sched_clock: 56 bits at 54MHz, resolution 18ns, wraps every 4398046511102ns
[    0.000760] Switching to timer-based delay loop, resolution 18ns
[    0.001015] Console: colour dummy device 80x30
[    0.001711] printk: console [tty0] enabled
[    0.001776] Calibrating delay loop (skipped), value calculated using timer frequency.. 108.00 BogoMIPS (lpj=540000)
[    0.001828] pid_max: default: 32768 minimum: 301
[    0.002014] LSM: Security Framework initializing
[    0.002216] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.002261] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.003851] Disabling memory control group subsystem
[    0.003985] CPU: Testing write buffer coherency: ok
[    0.004445] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.005635] Setting up static identity map for 0x200000 - 0x200060
[    0.005842] rcu: Hierarchical SRCU implementation.
[    0.006772] smp: Bringing up secondary CPUs ...
[    0.007967] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.009377] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.010727] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.010951] smp: Brought up 1 node, 4 CPUs
[    0.010997] SMP: Total of 4 processors activated (432.00 BogoMIPS).
[    0.011025] CPU: All CPU(s) started in HYP mode.
[    0.011051] CPU: Virtualization extensions available.
[    0.011892] devtmpfs: initialized
[    0.025491] VFP support v0.3: implementor 41 architecture 3 part 40 variant 8 rev 0
[    0.025913] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.025965] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.027855] pinctrl core: initialized pinctrl subsystem
[    0.028941] NET: Registered protocol family 16
[    0.032712] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[    0.033496] audit: initializing netlink subsys (disabled)
[    0.033760] audit: type=2000 audit(0.030:1): state=initialized audit_enabled=0 res=1
[    0.034366] thermal_sys: Registered thermal governor 'step_wise'
[    0.034812] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.034864] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.035231] Serial: AMBA PL011 UART driver
[    0.066503] bcm2835-mbox fe00b880.mailbox: mailbox enabled
[    0.080829] raspberrypi-firmware soc:firmware: Attached to firmware from 2021-02-25T12:10:40, variant start
[    0.090841] raspberrypi-firmware soc:firmware: Firmware hash is 564e5f9b852b23a330b1764bcf0b2d022a20afd0
[    0.136272] bcm2835-dma fe007000.dma: DMA legacy API manager, dmachans=0x1
[    0.140451] vgaarb: loaded
[    0.141234] SCSI subsystem initialized
[    0.141506] usbcore: registered new interface driver usbfs
[    0.141580] usbcore: registered new interface driver hub
[    0.141666] usbcore: registered new device driver usb
[    0.142011] usb_phy_generic phy: supply vcc not found, using dummy regulator
[    0.143646] clocksource: Switched to clocksource arch_sys_counter
[    1.138629] VFS: Disk quotas dquot_6.6.0
[    1.138764] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.138944] FS-Cache: Loaded
[    1.139158] CacheFiles: Loaded
[    1.149578] NET: Registered protocol family 2
[    1.150644] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    1.150709] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    1.150792] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    1.150880] TCP: Hash tables configured (established 8192 bind 8192)
[    1.151050] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    1.151104] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    1.151559] NET: Registered protocol family 1
[    1.152294] RPC: Registered named UNIX socket transport module.
[    1.152327] RPC: Registered udp transport module.
[    1.152353] RPC: Registered tcp transport module.
[    1.152380] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.152417] PCI: CLS 0 bytes, default 64
[    1.155375] Initialise system trusted keyrings
[    1.155642] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[    1.163550] zbud: loaded
[    1.165353] FS-Cache: Netfs 'nfs' registered for caching
[    1.166136] NFS: Registering the id_resolver key type
[    1.166195] Key type id_resolver registered
[    1.166222] Key type id_legacy registered
[    1.166383] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.167461] Key type asymmetric registered
[    1.167493] Asymmetric key parser 'x509' registered
[    1.167695] bounce: pool size: 64 pages
[    1.167751] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    1.167983] io scheduler mq-deadline registered
[    1.168013] io scheduler kyber registered
[    1.172393] brcm-pcie fd500000.pcie: host bridge /scb/pcie@7d500000 ranges:
[    1.172444] brcm-pcie fd500000.pcie:   No bus range found for /scb/pcie@7d500000, using [bus 00-ff]
[    1.172542] brcm-pcie fd500000.pcie:      MEM 0x0600000000..0x063fffffff -> 0x00c0000000
[    1.172650] brcm-pcie fd500000.pcie:   IB MEM 0x0000000000..0x007fffffff -> 0x0400000000
[    1.225750] brcm-pcie fd500000.pcie: link up, 5.0 GT/s PCIe x1 (SSC)
[    1.226138] brcm-pcie fd500000.pcie: PCI host bridge to bus 0000:00
[    1.226174] pci_bus 0000:00: root bus resource [bus 00-ff]
[    1.226209] pci_bus 0000:00: root bus resource [mem 0x600000000-0x63fffffff] (bus address [0xc0000000-0xffffffff])
[    1.226318] pci 0000:00:00.0: [14e4:2711] type 01 class 0x060400
[    1.226575] pci 0000:00:00.0: PME# supported from D0 D3hot
[    1.229741] PCI: bus0: Fast back to back transfers disabled
[    1.230111] pci 0000:01:00.0: [1106:3483] type 00 class 0x0c0330
[    1.230254] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit]
[    1.230737] pci 0000:01:00.0: PME# supported from D0 D3cold
[    1.233900] PCI: bus1: Fast back to back transfers disabled
[    1.234013] pci 0000:00:00.0: BAR 8: assigned [mem 0x600000000-0x6000fffff]
[    1.234054] pci 0000:01:00.0: BAR 0: assigned [mem 0x600000000-0x600000fff 64bit]
[    1.234156] pci 0000:00:00.0: PCI bridge to [bus 01]
[    1.234194] pci 0000:00:00.0:   bridge window [mem 0x600000000-0x6000fffff]
[    1.234633] pcieport 0000:00:00.0: enabling device (0140 -> 0142)
[    1.234867] pcieport 0000:00:00.0: PME: Signaling with IRQ 60
[    1.235804] bcm2708_fb soc:fb: FB found 1 display(s)
[    1.293441] Console: switching to colour frame buffer device 240x67
[    1.304517] bcm2708_fb soc:fb: Registered framebuffer for display 0, size 1920x1080
[    1.312330] iproc-rng200 fe104000.rng: hwrng registered
[    1.312699] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
[    1.313778] gpiomem-bcm2835 fe200000.gpiomem: Initialised: Registers at 0xfe200000
[    1.326731] brd: module loaded
[    1.339752] loop: module loaded
[    1.341532] Loading iSCSI transport class v2.0-870.
[    1.345057] libphy: Fixed MDIO Bus: probed
[    1.346793] bcmgenet fd580000.ethernet: GENET 5.0 EPHY: 0x0000
[    1.363681] libphy: bcmgenet MII bus: probed
[    1.443816] unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO bus
[    1.445090] usbcore: registered new interface driver r8152
[    1.445239] usbcore: registered new interface driver lan78xx
[    1.445365] usbcore: registered new interface driver smsc95xx
[    1.447050] xhci_hcd 0000:01:00.0: enabling device (0140 -> 0142)
[    1.447287] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    1.447384] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
[    1.450431] xhci_hcd 0000:01:00.0: hcc params 0x002841eb hci version 0x100 quirks 0x0000030000000890
[    1.451853] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    1.451959] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.452048] usb usb1: Product: xHCI Host Controller
[    1.452116] usb usb1: Manufacturer: Linux 5.10.17-v7l xhci-hcd
[    1.452193] usb usb1: SerialNumber: 0000:01:00.0
[    1.453042] hub 1-0:1.0: USB hub found
[    1.453187] hub 1-0:1.0: 1 port detected
[    1.454065] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    1.454152] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[    1.454254] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[    1.454843] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[    1.454943] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.455029] usb usb2: Product: xHCI Host Controller
[    1.455095] usb usb2: Manufacturer: Linux 5.10.17-v7l xhci-hcd
[    1.457914] usb usb2: SerialNumber: 0000:01:00.0
[    1.461492] hub 2-0:1.0: USB hub found
[    1.464362] hub 2-0:1.0: 4 ports detected
[    1.468832] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    1.471863] dwc_otg: FIQ enabled
[    1.471877] dwc_otg: NAK holdoff enabled
[    1.471891] dwc_otg: FIQ split-transaction FSM enabled
[    1.471908] Module dwc_common_port init
[    1.472362] usbcore: registered new interface driver uas
[    1.475244] usbcore: registered new interface driver usb-storage
[    1.478151] mousedev: PS/2 mouse device common for all mice
[    1.482504] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[    1.488890] sdhci: Secure Digital Host Controller Interface driver
[    1.491600] sdhci: Copyright(c) Pierre Ossman
[    1.495110] mmc-bcm2835 fe300000.mmcnr: could not get clk, deferring probe
[    1.498621] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.505897] ledtrig-cpu: registered to indicate activity on CPUs
[    1.508945] hid: raw HID events driver (C) Jiri Kosina
[    1.511822] usbcore: registered new interface driver usbhid
[    1.514548] usbhid: USB HID core driver
[    1.517575] ashmem: initialized
[    1.526079] Initializing XFRM netlink socket
[    1.528872] NET: Registered protocol family 17
[    1.531796] Key type dns_resolver registered
[    1.534628] Registering SWP/SWPB emulation handler
[    1.537451] registered taskstats version 1
[    1.540084] Loading compiled-in X.509 certificates
[    1.543576] Key type ._fscrypt registered
[    1.546264] Key type .fscrypt registered
[    1.548855] Key type fscrypt-provisioning registered
[    1.562835] uart-pl011 fe201000.serial: there is not valid maps for state default
[    1.565864] uart-pl011 fe201000.serial: cts_event_workaround enabled
[    1.568566] fe201000.serial: ttyAMA0 at MMIO 0xfe201000 (irq = 36, base_baud = 0) is a PL011 rev2
[    1.578843] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver
[    1.582711] mmc-bcm2835 fe300000.mmcnr: mmc_debug:0 mmc_debug2:0
[    1.585434] mmc-bcm2835 fe300000.mmcnr: DMA channel allocated
[    1.618520] of_cfs_init
[    1.621399] of_cfs_init: OK
[    1.637777] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[    1.642148] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    1.646411] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    1.651960] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[    1.654518] mmc0: SDHCI controller on fe340000.emmc2 [fe340000.emmc2] using ADMA
[    1.658716] Waiting for root device /dev/mmcblk0p2...
[    1.658920] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    1.698251] random: fast init done
[    1.701137] mmc0: new high speed SD card at address b368
[    1.704787] mmcblk0: mmc0:b368 SD    1.88 GiB
[    1.709349]  mmcblk0: p1 p2
[    1.719726] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    1.722376] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[    1.725703] devtmpfs: mounted
[    1.737724] Freeing unused kernel memory: 2048K
[    1.743053] mmc1: new high speed SDIO card at address 0001
[    1.784001] Run /sbin/init as init process
[    1.786547]   with arguments:
[    1.786561]     /sbin/init
[    1.786574]   with environment:
[    1.786588]     HOME=/
[    1.786601]     TERM=linux
[    1.823716] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[    2.026347] usb 1-1: New USB device found, idVendor=2109, idProduct=3431, bcdDevice= 4.21
[    2.029096] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    2.031770] usb 1-1: Product: USB2.0 Hub
[    2.036725] hub 1-1:1.0: USB hub found
[    2.039946] hub 1-1:1.0: 4 ports detected
[    2.373702] usb 1-1.3: new low-speed USB device number 3 using xhci_hcd
[    2.512986] usb 1-1.3: New USB device found, idVendor=046a, idProduct=b090, bcdDevice= 1.03
[    2.515805] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.518562] usb 1-1.3: Product: USB keyboard
[    2.521264] usb 1-1.3: Manufacturer: Cherry
[    2.537534] input: Cherry USB keyboard as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.0/0003:046A:B090.0001/input/input0
[    2.604618] hid-generic 0003:046A:B090.0001: input,hidraw0: USB HID v1.11 Keyboard [Cherry USB keyboard] on usb-0000:01:00.0-1.3/input0
[    2.618923] input: Cherry USB keyboard System Control as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.1/0003:046A:B090.0002/input/input1
[    2.658340] udevd[135]: starting version 3.2.9
[    2.671390] random: udevd: uninitialized urandom read (16 bytes read)
[    2.675667] random: udevd: uninitialized urandom read (16 bytes read)
[    2.678720] random: udevd: uninitialized urandom read (16 bytes read)
[    2.694152] input: Cherry USB keyboard Consumer Control as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.1/0003:046A:B090.0002/input/input2
[    2.697961] hid-generic 0003:046A:B090.0002: input,hiddev96,hidraw1: USB HID v1.11 Device [Cherry USB keyboard] on usb-0000:01:00.0-1.3/input1
[    2.715471] udevd[136]: starting eudev-3.2.9
[    3.429661] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[    5.557589] urandom_read: 2 callbacks suppressed
[    5.557600] random: dd: uninitialized urandom read (512 bytes read)
[    5.970580] bcmgenet fd580000.ethernet: configuring instance for external RGMII (RX delay)
[    5.974452] bcmgenet fd580000.ethernet eth0: Link is Down
[   15.876520] random: dbus-uuidgen: uninitialized urandom read (12 bytes read)
[   15.880013] random: dbus-uuidgen: uninitialized urandom read (8 bytes read)
[   16.580310] random: dbus-daemon: uninitialized urandom read (12 bytes read)
[   16.921103] random: crng init done
[   16.924555] random: 1 urandom warning(s) missed due to ratelimiting
[   27.264949] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   29.214076] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[   29.218059] NFSD: Using legacy client tracking operations.
[   29.221325] NFSD: starting 90-second grace period (net f0000089)
[  322.863688] usb 1-1.1: new high-speed USB device number 4 using xhci_hcd
[  322.994607] usb 1-1.1: New USB device found, idVendor=0781, idProduct=55a1, bcdDevice= 1.00
[  322.994628] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  322.994646] usb 1-1.1: Product: Cruzer Spark
[  322.994662] usb 1-1.1: Manufacturer: SanDisk
[  322.994678] usb 1-1.1: SerialNumber: 4C530000121018112041
[  323.002233] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[  323.003015] scsi host0: usb-storage 1-1.1:1.0
[  324.076230] scsi 0:0:0:0: Direct-Access     SanDisk  Cruzer Spark     1.00 PQ: 0 ANSI: 6
[  324.078390] sd 0:0:0:0: [sda] 60088320 512-byte logical blocks: (30.8 GB/28.7 GiB)
[  324.079745] sd 0:0:0:0: [sda] Write Protect is off
[  324.079776] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
[  324.080619] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[  324.147096]  sda: sda1
[  324.151858] sd 0:0:0:0: [sda] Attached SCSI removable disk
[  401.948325] EXT4-fs (sda1): recovery complete
[  401.949286] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)

also, is raspberrypi4 supported with meta-swupdate-boards or i need to create the bsp layer ?